Nuclear Fuel Breeding
All commercial light water reactors contains both fissile and fertile materials. For example, most PWRs use low enriched uranium fuel with enrichment of 235U up to 5%. Therefore more than 95% of content of fresh fuel is fertile isotope 238U. During fuel burnup the fertile materials (conversion of 238U to fissile 239Pu known as fuel breeding) partially replace fissile 235U, thus permitting the power reactor to operate longer before the amount of fissile material decreases to the point where reactor criticality is no longer manageable.
The fuel breeding in the fuel cycle of all commercial light water reactors plays a significant role. In recent years, the commercial power industry has been emphasizing high-burnup fuels (up to 60 – 70 GWd/tU), which are typically enriched to higher percentages of 235U (up to 5%). As burnup increases, a higher percentage of the total power produced in a reactor is due to the fuel bred inside the reactor.
From this point of view, the neutron is utilized much more effectively when captured by 238U than when captured by absorbator, because the effective multiplication factor must in every state equal to 1 (Note that in PWRs the boric acid is used to compensate an excess of reactivity of reactor core along thefuel cycle). In other words it is better to capture the neutron (lower an excess of reactivity) by 238U, rather than by 10B nuclei.
At HFP (hot full power) state, the fuel temperature is directly given by:
- Local linear heat rate (W/cm), which is given by neutron flux distribution. See also: Power Distribution
- Fuel-cladding gap. As the fuel burnup increases the fuel-cladding gap reduces. This reduction is caused by the swelling of the fuel pellets and cladding creep. Fuel pellets swelling occurs because fission gases cause the pellet to swell resulting in a larger volume of the pellet. At the same time, the cladding is distorted by outside pressure (known as the cladding creep). These two effects result in direct fuel-cladding contact (e.g. at burnup of 25 GWd/tU). The direct fuel-cladding contact causes a significant reduction in fuel temperature profile, because the overall thermal conductivity increases due to conductive heat transfer.
- Core inlet temperature. Core inlet temperature is directly given by system parameters in steam generators. When steam generators are operated at approximately 6.0MPa, it means the saturation temperature is equal to 275.6 °C. Since there must be always ΔT (~15°C) between the primary circuit and the secondary circuit, the reactor coolant (in the cold leg)have about 290.6°C (at HFP) at the inlet of the core. As the system pressure increases, the core inlet temperature must also increase. This increase causes slight increase in fuel temperature.
It can be summarized, the fuel breeding is lower, when the reactor is operated at lower power levels. Note that, in order to lower the reactor power, additional absorbators must be inserted inside the core. The fuel breeding is higher (e.g. 1 EFPD surplus), when the core inlet temperature of the reactor coolant is higher (e.g. 1°C for 300 EFPDs). It must be added, the inlet temperature is limited and it cannot be changed arbitrarily.
Comparison of cross-sections
Source: JANIS (Java-based nuclear information software) http://www.oecd-nea.org/janis/Uranium 238. Comparison of total fission cross-section and cross-section for radiative capture.Thorium 232. Comparison of total fission cross-section and cross-section for radiative capture.
Conversion Factor – Breeding Ratio
A quantity that characterizes this conversion of fertile into fissile material is known as the conversion factor. The conversion factor is defined as the ratio of fissile material created to fissile material consumed either by fission or absorption. If the ratio is greater than one, it is often referred to as the breeding ratio, for then the reactor is creating more fissile material than it is consuming.
When C is unity, one new atom is produced per one atom consumed. It seems fertile material can be converted in the reactor indefinitely without adding new fuel, but in real reactors the content of fertile uranium 238 also decreases and fission products with significant absorption cross-section accumulates in the fuel as fuel burnup increases.
If we use a simplified model, which includes only uranium and plutonium-239, the conversion factor is:
This equation indicates that increased fuel enrichment results in a decreased value of C(0), the initial conversion factor. As the content of fissile material decreases with fuel burnup, the conversion factor increases. As this happens an increasing fraction of the fission comes from plutonium.
See also: Conversion Factor