Contents
Diesel Cycle – Diesel Engine
In the 1890s, a German inventor, Rudolf Diesel has patented his invention of an efficient, slow burning, compression ignition, internal combustion engine. The original cycle proposed by Rudolf Diesel was a constant temperature cycle. In later years Diesel realized his original cycle would not work and he adopted the constant pressure cycle, which is known as the Diesel cycle.
Diesel cycle is one of most common thermodynamic cycles that can be found in automobile engines and describes the functioning of a typical compression ignition piston engine. The Diesel engine is similar in operation to the gasoline engine. The most important difference is that:
 There is no fuel in the cylinder at the beginning of the compression stroke, therefore an autoignition does not occur in Diesel engines.
 Diesel engine uses compression ignition instead of spark ignition.
 Because of the high temperature developed during the adiabatic compression, the fuel ignites spontaneously as it is injected. Therefore no spark plugs are needed.
 Before the beginning of the power stroke, the injectors start to inject fuel directly into the combustion chamber and therefore first part of power stroke occurs approximately at the constant pressure.
 Higher compression ratios can be achieved in Diesel engines, than in Otto engines
Since Carnot’s principle states that no engine can be more efficient than a reversible engine (a Carnot heat engine) operating between the same high temperature and low temperature reservoirs, the Diesel engine must have lower efficiency than the Carnot efficiency. A typical diesel automotive engine operates at around 30% to 35% of thermal efficiency. About 6570% is rejected as waste heat without being converted into useful work, i.e. work delivered to wheels. In general, engines using the Diesel cycle are usually more efficient, than engines using the Otto cycle. The diesel engine has the highest thermal efficiency of any practical combustion engine. Lowspeed diesel engines (as used in ships) can have a thermal efficiency that exceeds 50%. The largest diesel engine in the world peaks at 51.7%.
Diesel Cycle – Processes
In an ideal Diesel cycle, the system executing the cycle undergoes a series of four processes: two isentropic (reversible adiabatic) processes alternated with one isochoric process and one isobaric process.

Isentropic compression (compression stroke) – The air is compressed adiabatically from state 1 to state 2, as the piston moves from bottom dead center to top dead center. The surroundings do work on the gas, increasing its internal energy (temperature) and compressing it. On the other hand the entropy remains unchanged. The changes in volumes and its ratio (V_{1} / V_{2}) is known as the compression ratio.
 Isobaric expansion (ignition phase) – In this phase (between state 2 and state 3) there is a constantpressure (idealized model) heat transfer to the air from an external source (combustion of injected fuel) while the piston is moving toward the V_{3}. During the constant pressure process, energy enters the system as heat Q_{add}, and a part of work is done by moving piston.
 Isentropic expansion (power stroke) – The gas expands adiabatically from state 3 to state 4, as the piston moves from V_{3} to bottom dead center. The gas does work on the surroundings (piston) and loses an amount of internal energy equal to the work that leaves the system. Again the entropy remains unchanged. The volume ratio (V_{4} / V_{3}) is known as the isentropic expansion ratio.
 Isochoric decompression (exhaust stroke) – In this phase the cycle completes by a constantvolume process in which heat is rejected from the air while the piston is at bottom dead center. The working gas pressure drops instantaneously from point 4 to point 1. The exhaust valve opens at point 4. The exhaust stroke is directly after this decompression. As the piston moves from bottom dead center (point 1) to top dead center (point 0) with the exhaust valve opened, the gaseous mixture is vented to the atmosphere and the process starts anew.
During the Diesel cycle, work is done on the gas by the piston between states 1 and 2 (isentropic compression). Work is done by the gas on the piston between stages 2 and 3 (isobaric heat addition) and between stages 2 and 3 (isentropic expansion). The difference between the work done by the gas and the work done on the gas is the net work produced by the cycle and it corresponds to the area enclosed by the cycle curve. The work produced by the cycle times the rate of the cycle (cycles per second) is equal to the power produced by the Diesel engine.
Isentropic Process
An isentropic process is a thermodynamic process, in which the entropy of the fluid or gas remains constant. It means the isentropic process is a special case of an adiabatic process in which there is no transfer of heat or matter. It is a reversible adiabatic process. The assumption of no heat transfer is very important, since we can use the adiabatic approximation only in very rapid processes.
Isentropic Process and the First Law
For a closed system, we can write the first law of thermodynamics in terms of enthalpy:
dH = dQ + Vdp
or
dH = TdS + Vdp
Isentropic process (dQ = 0):
dH = Vdp → W = H_{2} – H_{1} → H_{2} – H_{1} = C_{p} (T_{2} – T_{1}) (for ideal gas)
Isentropic Process of the Ideal Gas
The isentropic process (a special case of adiabatic process) can be expressed with the ideal gas law as:
pV^{κ} = constant
or
p_{1}V_{1}^{κ} = p_{2}V_{2}^{κ}
in which κ = c_{p}/c_{v} is the ratio of the specific heats (or heat capacities) for the gas. One for constant pressure (c_{p}) and one for constant volume (c_{v}). Note that, this ratio κ = c_{p}/c_{v} is a factor in determining the speed of sound in a gas and other adiabatic processes.
Isochoric Process
An isochoric process is a thermodynamic process, in which the volume of the closed system remains constant (V = const). It describes the behavior of gas inside the container, that cannot be deformed. Since the volume remains constant, the heat transfer into or out of the system does not the p∆V work, but only changes the internal energy (the temperature) of the system.
Isochoric Process and the First Law
The classical form of the first law of thermodynamics is the following equation:
dU = dQ – dW
In this equation dW is equal to dW = pdV and is known as the boundary work. Then:
dU = dQ – pdV
In isochoric process and the ideal gas, all of heat added to the system will be used to increase the internal energy.
Isochoric process (pdV = 0):
dU = dQ (for ideal gas)
dU = 0 = Q – W → W = Q (for ideal gas)
Isochoric Process of the Ideal Gas
The isochoric process can be expressed with the ideal gas law as:
or
On a pV diagram, the process occurs along a horizontal line that has the equation V = constant.
See also: GuyLussac’s Law
Isobaric Process
An isobaric process is a thermodynamic process, in which the pressure of the system remains constant (p = const). The heat transfer into or out of the system does work, but also changes the internal energy of the system.
Since there are changes in internal energy (dU) and changes in system volume (∆V), engineers often use the enthalpy of the system, which is defined as:
H = U + pV
Isobaric Process and the First Law
The classical form of the first law of thermodynamics is the following equation:
dU = dQ – dW
In this equation dW is equal to dW = pdV and is known as the boundary work. In an isobaric process and the ideal gas, part of heat added to the system will be used to do work and part of heat added will increase the internal energy (increase the temperature). Therefore it is convenient to use the enthalpy instead of the internal energy.
Isobaric process (Vdp = 0):
dH = dQ → Q = H_{2}– H_{1}
At constant entropy, i.e. in isentropic process, the enthalpy change equals the flow process work done on or by the system.
Isobaric Process of the Ideal Gas
The isobaric process can be expressed with the ideal gas law as:
or
On a pV diagram, the process occurs along a horizontal line (called an isobar) that has the equation p = constant.
See also: Charles’s Law
Comparison of Actual and Ideal Diesel Cycles
In this article it is shown an ideal Diesel cycle in which there are a lot of assumptions differs from actual Diesel cycle. The main differences between the actual and ideal Diesel engine appear in the figure. In reality, the ideal cycle does not occur and there are many losses associated with each process. For an actual cycle, the shape of the pV diagram is similar to the ideal, but the area (work) enclosed by the pV diagram is always less than the ideal value. The ideal Diesel cycle is based on the following assumptions:
 Closed cycle: The largest difference between the two diagrams is the simplification of the intake and exhaust strokes in the ideal cycle. In the exhaust stroke, heat Q_{out} is ejected to the environment (in a real engine, the gas leaves the engine and is replaced by a new mixture of air and fuel).
 Isobaric heat addition. In real engines the heat addition is never isobaric.
 No heat transfer
 Compression – The gas is compressed adiabatically from state 1 to state 2. In real engines, there are always some inefficiencies that reduce the thermal efficiency.
 Expansion. The gas expands adiabatically from state 3 to state 4.
 Complete combustion of the mixture.
 No pumping work. Pumping work is the difference between the work done during exhaust stroke and the work done during intake stroke. In real cycles, there is a pressure difference between exhaust and inlet pressures.
 No blowdown loss. Blowdown loss is caused by the early opening of exhaust valves. This results in a loss of work output during expansion stroke.
 No blowby loss. The blowby loss is caused by the leakage of compressed gases through piston rings and other crevices.
 No frictional losses.
These simplifying assumptions and losses lead to the fact that the enclosed area (work) of the pV diagram for an actual engine is significantly smaller than the size of the area (work) enclosed by the pV diagram of the ideal cycle. In other words, the ideal engine cycle will overestimate the net work and, if the engines run at the same speed, greater power produced by the actual engine by around 20% (similarly as in the case of Otto engine).
Thermal Efficiency for Diesel Cycle
In general the thermal efficiency, η_{th}, of any heat engine is defined as the ratio of the work it does, W, to the heat input at the high temperature, Q_{H}.
The thermal efficiency, η_{th}, represents the fraction of heat, Q_{H}, that is converted to work. Since energy is conserved according to the first law of thermodynamics and energy cannot be be converted to work completely, the heat input, Q_{H}, must equal the work done, W, plus the heat that must be dissipated as waste heat Q_{C} into the environment. Therefore we can rewrite the formula for thermal efficiency as:
The heat absorbed occurs during combustion of fuelair mixture, when the spark occurs, roughly at constant volume. Since during an isochoric process there is no work done by or on the system, the first law of thermodynamics dictates ∆U = ∆Q. Therefore the heat added and rejected are given by:
Q_{add} = mc_{p} (T_{3} – T_{2})
Q_{out} = mc_{v} (T_{4} – T_{1})
Substituting these expressions for the heat added and rejected in the expression for thermal efficiency yields:
This equation can be rearranged to the form with the compression ratio and the cutoff ratio:
where
 η_{Diesel} is the maximum thermal efficiency of a Diesel cycle
 α is the cutoff ration V_{3}/V_{2} (i.e. the ratio of volumes at the end and start of the combustion phase)
 CR is the compression ratio
 κ = c_{p}/c_{v} = 1.4
It is very useful conclusion, because it is desirable to achieve a high compression ratio to extract more mechanical energy from a given mass of the fuel. As we have concluded in previous section the airstandard Otto cycle thermal efficiency is also a function of compression ratio and κ.
When we compare these to formulae, it can be seen that for a given compression ratio (CR), the Otto cycle will be more efficient than the Diesel cycle . But diesel engines are usually be more efficient since they are able to operate at higher compression ratios.
In ordinary Otto engines the compression ratio has its limits. The compression ratio in a gasolinepowered engine will usually not be much higher than 10:1. Higher compression ratios will make gasoline engines subject to engine knocking, caused by autoignition an unburned mixture, if lower octanerated fuel is used. In diesel engines there is minimal risk of autoignition of the fuel, because diesel engines are compressionignition engines and there is no fuel in the cylinder at the beginning of the compression stroke.
Diesel Cycle – Problem with Solution
Let assume the Diesel cycle, which is the one of most common thermodynamic cycles that can be found in automobile engines. One of key parameters of such engines is the change in volumes between top dead center (TDC) to bottom dead center (BDC). The ratio of these volumes (V_{1} / V_{2}) is known as the compression ratio. Also the cutoff ratio V_{3}/V_{2}, which is the ratio of volumes at the end and start of the combustion phase.
In this example let assume the Diesel cycle with compression ratio of CR = 20 : 1 and cutoff ratio α = 2. The air is at 100 kPa = 1 bar, 20 °C (293 K), and the volume of the chamber is 500 cm³ prior to the compression stroke.
 Specific heat capacity at constant pressure of air at atmospheric pressure and room temperature: c_{p} = 1.01 kJ/kgK.
 Specific heat capacity at constant volume of air at atmospheric pressure and room temperature: c_{v} = 0.718 kJ/kgK.
 κ = c_{p}/c_{v} = 1.4
Calculate:
 the mass of intake air
 the temperature T_{2}
 the pressure p_{2}
 the temperature T_{3}
 the amount of heat added by burning of fuelair mixture
 the thermal efficiency of this cycle
 the MEP
Solution:
1)
At the beginning of calculations we have to determine the amount of gas in the cylinder before the compression stroke. Using the ideal gas law, we can find the mass:
pV = mR_{specific}T
where:
 p is the absolute pressure of the gas
 m is the mass of substance
 T is the absolute temperature
 V is the volume
 R_{specific} is the specific gas constant, equal to the universal gas constant divided by the molar mass (M) of the gas or mixture. For dry air R_{specific} = 287.1 J.kg^{1}.K^{1}.
Therefore
m = p_{1}V_{1}/R_{specific}T_{1} = (100000 × 500×10^{6} )/(287.1 × 293) = 5.95×10^{4} kg
2)
In this problem all volumes are known:
 V_{1} = V_{4} = V_{max} = 500×10^{6} m^{3} (0.5l)
 V_{2} = V_{min} = V_{max} / CR = 25 ×10^{6} m^{3}
Note that (V_{max} – V_{min}) x number of cylinders = total engine displacement
Since the process is adiabatic, we can use the following p, V, T relation for adiabatic processes:
thus
T_{2} = T_{1} . CR^{κ – 1} = 293 . 20^{0.4} = 971 K
3)
Again, we can use the ideal gas law to find the pressure at the end of the compression stroke as:
p_{2} = mR_{specific}T_{2} / V_{2} = 5.95×10^{4} x 287.1 x 971 / 25 ×10^{6} = 6635000 Pa = 66.35 bar
4)
Since process 2 → 3 occurs at constant pressure, the ideal gas equation of state gives
T_{3} = (V_{3}/V_{2}) x T_{2} = 1942 K
To calculate the amount of heat added by burning of fuelair mixture, Q_{add}, we have to use the first law of thermodynamics for isobaric process, which states:
Q_{add} = mc_{p} (T_{3} – T_{2}) = 5.95×10^{4} x 1010 x 971 = 583.5 J
5)
Thermal efficiency for this Diesel cycle:
As was derived in the previous section, the thermal efficiency of Diesel cycle is a function of the compression ratio, the cutoff ratio and κ:
 η_{Diesel} is the maximum thermal efficiency of a Diesel cycle
 α is the cutoff ration V_{3}/V_{2} (i.e. the ratio of volumes at the end and start of the combustion phase)
 CR is the compression ratio
 κ = c_{p}/c_{v} = 1.4
For this example:
η_{Diesel} = 0.6467 = 64.7%
6)
The MEP was defined as:
It this equation the displacement volume is equal to V_{max} – V_{min}. The net work for one cycle can be calculated using the heat added and the thermal efficiency:
W_{net} = Q_{add} . η_{Otto} = 583.5 x 0.6467 = 377.3 J
MEP = 377.3 / (500×10^{6} – 25 ×10^{6}) = 794.3 kPa = 7.943 bar